India's Largest Stockist and Supplier Of Nickel Alloys Since 2007

IN100

IN100 Spot Lights
Alloy Grade K417(K17、M17)
Related Grades IN100
Material Group S - Superalloys (Heat resistant and Titanium)
Sub-Group Superalloy
Tensile Strength [N/mm^2]
Machinability Range 15% - 45%
Size Grades
  • 105+45micron
  • -53+15micron
AMS Specification 5397
Appearance Gray metallic powder

Get IN100 as per Standards Click Here

 

IN100 Specification

 

Table of Content
Regent Steel & Engineering Co.

UNS N13100 Alloy Supplier in India, Refer Chemical Composition

UNS N13100 Alloy Chemical Composition
Element Amount
Cobalt (Co) 15%
Titanium (Ti) 4.7%
Molybdenum (Mo) 3%
Chromium (Cr) 10%
Aluminum (Al) 5.5%
Nickel (Ni) 61.6%
Carbon (C) 0.18%

Offer SAE 5397 Material With High Rupture Strength Through 1900 ºF At Discounted Price

SAE 5397 Material High Rupture Strength
Test Temp. °F Stress psi Life Hrs. E Long % in 4d
7.75 g/cu.cm 1260 - 1350 °c 1260 - 1350 °c 1260 - 1350 °c
IN100 Material Stress Rupture Properties
Test Temp. Stress, psi, for Rupture
°F 10 hr. 100 hr. 1000 hr.
1350 - 97,000 83,000
1500 90,000 73,000 55,000
1700 52,000 38,000 25,000
1800 38,000 25,000 15,000
1900 - 16,000 8,500
Recommended Carbide Grades for Material IN100
Grades for Turning Grades for Milling Grades for Parting Off Grades for Grooving
S05F S30T GC1105 GC1125
S205 S40T GC1145 IC806 (IC804)
GC1205 (GC1105) IC808 (IC908) IC807 (IC907) IC808 (IC908)
GC1210 IC830 (IC928) IC808 (IC908) IC830 (IC328)
GC1125 KC510M IC830 (IC328) KCU10
IC806 (IC804) KC522M KCU10 KCU25
IC807 (IC907) KCSM40 KCU25 WSM13S
IC830 (IC328) MS2500 WSM13S WSM23S
KCU10B (KCU10) F40M WSM23S WSM33S (WSM33)
KCU25 (KC5025) MS2050 WSM33S (WSM33) WSM43S
WSM10S (WSM10) AH120 WSM43S CP500
WSM01 AH725 CP500 CP600
WSM20S (WSM20) CTP6215 CP600 AH905
WSM30S (WSM30) CTPX715 AH7025 AH7025
TS2000 (CP200) CTCS245 AH725 AH725
CP500 CTC5240 CTCP325 CTCP325
CP600 MP9120 CTP1340 CTP1340
TS2500 MP9130 CTPP345 CTPP345
AH8005 ACU2500 VP10RT VP10RT
AH8015 ACM200 VP20RT VP20RT
CTPX710 ACM300 VP30RT VP30RT
CTPX715 - AC520U AC520U
MP9005 - AC1030U (AC530U) AC1030U (AC530U)
MP9015 - - -
VP20RT - - -
AC5005S (AC510U) - - -
AC5015S - - -
AC5025S (AC520U) - - -
IN100 Material Cutting Speeds Recommendation
Application Vc (SFM) Vc (m/min)
Turning 200-590 60-180
Milling 150-440 45-135
Parting 130-380 40-115
Grooving 180-520 55-160
Drilling 150-440 45-135
Recommended Insert Cutting Edge Geometry for Material IN100
Honing Size: 0.02-0.05 mm / 0.001-0.002"
Land Width: 0.10-0.20 mm / 0.004-0.008"
Land Angle: Neutral
Rake Angle: 13° -18°
Ground Insert: Recommended

Stockist Of Nickel-Base Precipitation Hardenable and Vacuum Cast Alloy WNR 2.4674 Powder in Mumbai , Refer Equivalent

IN100 Alloy Equivalent
Standard Name
UNS UNS N13100
WNR 2.4674
SAE 5397
DIN NiCo15Cr10MoAlTi
AFNOR NK15CAT
High Performance Nickel Based NiCo15Cr10MoAlTi Superalloy Creep Rate
Test Temp. Stress, psi, for Designated Creep Rate
°F .0001%/hr. .001 %/ hr. .01%/hr.
1350 - 77,500 95,000
1500 (47,000) 55,000 70,000
1700 (12,000) 22,500 34,000
1800 (6,500) 14,500 22,500
1900 - 5,000 13,500
Creep Rupture Curves for IN-100 Alloys at 1350 °F
Creep Rupture Curves for IN-100 Alloys

 

Long - Time Creep Data of IN-100 Alloy
Temp. Stress Minimum Time, Hours, for Total Creep Strain
°F psi Creep Rate %/Hr. 0.1% 0.2% 0.5% 1.0%
1350 100,000 .0291 1.0 2.0 8.0 26
90,000 .0050 5.0 10 44 135
80,000 .0014 25 175 500 800
1500 85,000 .1300 - 0.2 1.9 5.6
75,000 .0185 2.0 2.5 7.7 28
55,000 .0010 50 170 395 560
1700 50,000 .0320 0.4 1.8 2.9 5.8
19,000 .0004 80 200 1000 1760
1800 29,000 .0310 1.5 7.0 16 25
25,000 .0350 2.5 7.0 19 35
13,000 .0006 60 175 625 1175
12,000 .0005 75 195 750 1380
1900 15,000 .0144 2.7 6.0 25 58
12,000 .0060 8.0 20 62 140
9,000 .0028 4.0 15 90 270
Recommended Conditions For Machining IN-100 Alloy
Operation Tool Material Depth of Cut inches Tool Used for Tests  Feed Cutting Speed ft./min, Tool
life		 Wear- land inches Cutting Fluid
Drilling M-42 HSS .250 thru 1/4" diameter drill
2-1/2" long		 .003
in. /
rev.		 5 25
holes		 0.015 Highly
Chlorinated
Oil
Turning C.3
Carbide		 .075 1/4" square throwaway insert .009
in. /
rev.		 30 12
min.		 0.015 Highly
Sulphurized
OU
Drilling C-2
Carbide		 .250 thru 1/4" diameter drill               .
2"1ong		 .003
in. /
rev..		 14 21
holes		 0.015 Highly
Chlorinated
OU
SAE 5397 Alloy Surface Grinding
Operation Grinding Fluid Table Speed Ft./Min Wheel Speed Ft./Min Down Feed in./Pass Cross Feed in./Pass G Ratio
Roughing Highly Sulphurized Oil 60 3000-4000 .001 .050 4.5
Finishing Highly Sulphurized Oil 60 3000-4000 .0005 .050 3.5
Get Cyclic and Static Tested NiCo15Cr10MoAlTi Superalloy For High-Temperature Applications
ANFOR NK15CAT Alloy Testings
  • Cyclic Test
  • Static Test
  • Dynamic Test
  • Crucible Test
  • Rig Test

NiCo15Cr10MoAlTi Superalloy Applications
NiCo15Cr10MoAlTi Superalloy Applications

 

ANFOR NK15CAT Material With Density 7.75 g/cu.cm, Check Mechanical and Physical Properties
ANFOR NK15CAT Material Mechanical Properties
Test Temp. °F Tensile Strength psi 0.2% Yield Strength psi Reduction of Area Elong. %
70 147000 123000 11.0 9.0
1000 158000 128000 11.0 9.0
1200 161000 129000 7.0 6.0
1350 159000 127000 7.2 6.5
1500 144000 118000 7.2 6.0
1700 107000 73000 7.2 6.0
1900 64000 41000 8.0 6.0
Thermal Expansion of SAE 5397 Alloy
Test Temp. °F Mean Coefficient per °F Test Temp. °F Mean Coefficient per °F
70 - 200 7.2 x 10• 70-1200 8.0 x 10•
70 - 400 7.2 70-1400 8.3
70 - 600 7.3 70 -1600 8.8
70 - 800 7.5 70 -1800 9.3
70 -1000 7.7 70-2000 10.1
Physical Properties of NiCo15Cr10MoAlTi Superalloy
Dencity Melting Point
7.75 g/cu.cm 1260 - 1350 °c
UNS N13100 Dynamic Modulus Of Elasticity
Test Temp. Dynamic Modulus Test Temp. Dynamic Modulus
°F psi °F psi
70 31.2 X 10 1000 27.1
200 30.7 1200 26.0
400 29.9 1400 25.1
600 28.9 1600 23.5
800 28.1 1800 21.9
Thermal Fatigue Resistance of WNR 2.4674 Material
Alloy Peak Temperature
1472 °F (800 °C) 1652 °F (900 °C) 1832 °F (1000°C)
IN100 >1372 107 29
IN100 Alloy Powder Hardness
Test Temp. Hardness Test Temp. Hardness
°F Rc °F Rc
70 38.0 1200 35.5
600 37.5 1400 34.5
800 37.5 1600 29.0
1000 35.5 1800 16.0
Impact Properties of IN100 Alloy
Holding Time, Hr. Grain Size Holding Temperature
R.T. 1200 °F 1500 °F 1700 °F
0 1/16" 79, 73 - - -
- 1/4 45, 67 - - -
500 1/16 - 55, 89 45, 35 24, 25
- 1/4 - 53, 48 38, 32 23, 36
1000 1/16 - 69, 60 44, 19 28, 24
- 1/4 - 39, 45 39, 45 31, 24
Regent Steel

Why Should You Buy From Regent Steel?

  • Distributor of Renowned Mills of Nickel Alloys in Europe and USA.
  • Experience of 2 Decades as a Supplier of High Temperature Alloys in Dubai ( UAE), Saudi Arabia and Africa.
  • Largest Stockist of Nickel Alloy Flat Products in Mumbai
  • Ready Stock of Sheets, Coils, Strips and Bars in Over 50 Sizes at Al Jubail, Abu Dhabi, Muscat and South Africa
  • Facility of Cut to Size at No Extra Cost.
  • Weekly Delivery to Nigeria, Qatar, Dammam, Sharjah and Singapore
  • NACE Certified Material at Dealer Price.
  • Resale Price for Traders, Wholesalers, Importers and Stockholders in Mena Countries
  • Data Sheets and MTC Along With Quote.
  • Free Sample, Latest Price List on Request
  • Renowned Supplier in Heat Exchangers, Instrumentation, and Oil and Gas Industry
  • Compare Weight Chart and Price Per Kg in China and India.

Master Super Alloys

Wrought Super Alloys

Check Our Product Range

Get in touch

Call

+91-22-6639 4858

Email

export@regentsteel.com

close

© Copyright Regent Steel & Engg.Co. 2026. All Right Reserved.