Inconel 600 fasteners

  • Home
  • Inconel 600 fasteners
inconel 600 fasteners
What is Inconel 600 fasteners?

A combination of Chromium, Nickel and Iron, Inconel 600 fasteners provide a standard material for preventing rust or corrosion. It offers good oxidation resistance at high temperatures, especially in chloride and carburizing environments. Adding to this, nickel alloy 600 rivets is mainly designed for use from cryogenic to high temperatures till 2000° F (1093 ° C).

In most of the organic and inorganic compounds and even in reducing conditions, it offers excellent corrosion resistance because of the presence of higher contents of Nickel. Another advantage of this is that it also provides excellent resistance to chloride-ion stress-corrosion cracking. Addition of Chromium gives this material excellent resistance to sulphur compounds.

Table of content

We are extremely reliable alloy 600 hex bolts and nut supplier in India according to ASTM B166, check its highest temperature range

What is the highest temperature at which Inconel 600 bolts can be used?

Not only it provides good corrosion resistance, Inconel 600 bolts operates well and provide extensively good corrosion resistance at temperatures ranging from Cryogenic to elevated temperatures up to 2000° F. But specific temperature required depends on factors such as exposure duration, presence of any aggressive elements, and specific requirement. Other factor depends upon the demands made by industry or customers. This is also the reason why it provides good resistance to reducing environments and exceptional resistance to corrosion cracking.

Our primary focus is on the supply, stock, and timely delivery of cut-to-size UNS N06600 studs and threaded rod in Mumbai. must understand about inconel 600 bolts torque value

Alloy 600 hex bolts

Alloy 600 hex bolts

Inconel 600 bolts

Inconel 600 bolts

DIN 2.4816 threaded rod

DIN 2.4816 threaded rod

What is the torque value for Alloy 600 hex bolts?

Based on factors such as size, pitch of thread, and specific application, the torque value for any alloy 600 hex bolts shows variations. Torque is applied to deform the bolt stank elastically. In other words, torque applied is a function of frictional force and bolt diameter. They are calculated using clamp load which equals almost 60% of the output or yield. Factors such as material, fastener condition, surface finish and lubrication decide the actual clamp load.

Based on this, for a bolt/screw with dimension ¼’’ torque in dry condition is between 17-19 and in lubricated conditions is 12-14. This dimension values go up to 1-1/2’’ which have value of 3921-4412, and 2940-3308 in lubricated conditions. These values are calculated from Yield strength value of 185 ksi. You can check out the exact specifications of this material from regentsteel.com and purchase the product from there too.

Fully authorised stockist of DIN 2.4816 screws and washer with metric size ranging from M2 to M36 and lengths 3mm to 200 mm use for airframe components

Inconel 600 bolts specification
inconel 600 fasteners specification

 

CNC Machined Hot Forged Length
M100/4" Dia, M36/1-1/2 " Dia upto 1500 mm
Thread Specification Application
BSW, METRIC, UNF, UNC, BSF, custom ASTM B166 | ASME SB166 Food processing, nuclear engg
You have the opportunity to purchase Inconel Alloy 600 rivets and dowel pib at a low cost only here; shop for various types online to cut costs
List of Inconel 600 fasteners types
UNS N06600 nuts

UNS N06600 nuts

  • Size: M02 to M160
  • Length: 3 to 200 mm
  • ASTM B166 | ASME SB166
Inconel alloy 600 stud

Inconel alloy 600 stud

  • UNC
  • BSW, UNF
  • BSF, METRIC
Nickel alloy 600 screws

Nickel alloy 600 screws

  • Teflon coated
  • Zinc coated
  • Hot Dipped Galvanizing
As a trusted Inconel 600 fasteners manufacturer, we can assist you with all of your nickel alloy 600 socket head cap screw, flat washers etc stock supply requirements, View its various properties here.
Alloy 600 hex bolts equivalent
GRADE OLD BRITISH JIS UNS G0ST AFNOR OR
Inconel 600 EN BS NCF 600 N0600 XH60BT NC15FE11M ЭИ868
NiCr15Fe NA 14
UNS N06600 studs mechanical properties
Element Tensile Strength Melting Point Yield Strength (0.2%Offset) Density Elongation
Inconel 600 Psi – 95,000 , MPa – 655 1413 °C (2580 °F) Psi – 45,000 , MPa – 310 8.47 g/cm3 40 %
DIN 2.4816 threaded rod chemical properties
Grade Cr S Ni Fe Mn C Si P Cu
Inconel 600 Min %. 14 6
Max%. 17 0.015 72 10 1 0.15 0.5 0.015 0.5
What are the advantages of using DIN 2.4816 threaded rod?

DIN 2.4816 threaded rod exhibits lot of advantages. Known to show excellent corrosion resistance properties and withstand extreme temperature condition from cryogenic to high temperatures, they have good tensile strength of 100000 psi, when in annealed conditions. When hard rolled, the value increases to 125000 psi. This value of strength makes it prone to endure temperatures up to 1600° F. In addition, it shows good resistance to salt water, and can weld well enough in annealed and aged state. This makes it easy for use.

What precautions should be taken when installing Inconel 600 nuts ?

Precautionary steps must be taken while you install ASTM B166 Inconel 600 nuts.

  • First step for this is to first look out for clean surface. Make sure that that the surface which is threaded is clean and free of impurities. Next step is to follow the rules mentioned in manufacturing procedure or guidelines to prevent situations such as over-tightening completely.
  • After this step, next comes up the lubrication, where we properly apply lubrication to the threads to prevent galling and be sure of smooth tightening. Very important to note that choose the appropriate tools needed to yield excellent torque value. Make sure to avoid stressing the nut, considering expansion or contractions due to high temperatures as a factor.
  • Then make sure to keep check of proper thread alignment to prevent cross-threading. After installation, check or recheck for the torque value, engagement and alignment for a secure connection and long durability.
What is difference between Alloy 600 stud and bolt?

Although, Inconel alloy 600 stud and bolts are main two types of fasteners which are used for joining two components, they have some characteristic differences when brought into comparison. When comparing both with respect to its manufacturing or design, bolts have a threaded shaft at one end, while on the other hand, stud 600 have threads on both ends, having plain shank in middle.

Bolts on one hand are threaded into single material, whereas stud are used to connect two materials together with each end containing a nut. Adding to this, bolts are installed by just threading them to any one single component, while 600 studs are installed by threading one end into one component, and other end to other component or second component.

Finishes of nickel alloy 600 dowel pins
  • Hot Dipped Galvanized(HDG)
  • Zinc Plated
  • Zinc and Chromate
  • Plain Finish
  • Zinc and Yellow Chromate
Inconel alloy 600 stud bolt sizes
Stud bolt size Length of Stud Bolts
NPS Number of Bolts The diameter of Bolt Circle Outside Diameter of Flange The diameter of Bolt Holes Diameter of Bolts Ring Joint Raised Face
0.06 in
1/2 4 2 3/8 3 1/2 5/8 1/2 2 1/4
24 20 29 1/2 32 1 1/4 1 1/4 7 1/4 6 3/4
1 1/4 4 3 1/2 4 5/8 5/8 1/2 3 1/4 2 3/4
2 4 4 3/4 6 3/4 5/8 3 3/4 3 1/4
1 4 3 1/8 4 1/4 5/8 1/2 3 2 1/2
2 1/2 4 5 1/2 7 3/4 5/8 4 3 1/2
3 1/2 8 7 8 1/2 3/4 5/8 4 3 1/2
3 4 6 7 1/2 3/4 5/8 4 3 1/2
4 8 7 1/2 9 3/4 5/8 4 3 1/2
6 8 9 1/2 11 7/8 3/4 4 1/2 4
5 8 8 1/2 10 7/8 3/4 4 1/4 3 3/4
8 8 11 3/4 13 1/2 7/8 3/4 4 3/4 4 1/4
12 12 17 19 1 7/8 5 1/4 4 3/4
10 12 14 3/4 16 1 7/8 5 4 1/2
14 12 18 3/4 21 1 1/8 1 5 3/4 5 1/4
1 1/2 4 3 7/8 5 5/8 1/2 3 1/4 2 3/4
18 16 22 3/4 25 1 1/4 1 1/8 6 1/4 5 3/4
16 16 21 1/4 23 1/2 1 1/8 1 5 3/4 5 1/4
20 20 25 27 1/2 1 1/4 1 1/8 6 3/4 6 1/4
close