Call us 10:00 am - 6:00 pm

+91-22-2388 4555 / 4556

E-mail us

export@regentsteel.com

Inconel 600 Filler Wire

  • Home
  • Inconel 600 Filler Wire
Inconel 600 Filler Wire
How do you remove moisture from a inconel 600 filler wire?
  • You should start by looking out for visible signs of moisture and dry them up.
  • Preheat an oven to a low temperature of around 120 °C before placing inconel 600 filler wire. Ensure to use a clean tray and spread the wire evenly to allow proper airflow.
  • The drying time will increase with the diameter of the wire and the level of moisture.
  • Keep the filler wire in the oven until it cools down to room temperature. This will prevent moisture reabsorption due to rapid temperature drop.
  • The wire must be stored in sealed containers in a dry environment.
Table of content

As an inexpensive supplier of alloy 600 welding rod in India, we have a great deal of experience.

What is alloy 600 filler weld size?

The size of the filler weld for Alloy 600 can vary with the specific welding application and joint design. The inconel 600 welding wire weld size is determined by the welding procedure, base metal thickness, and joint configuration. A few general considerations are:

  • The width of the filler weld is determined by the joint design and the required weld strength.
  • The depth of the filler weld is typically determined by the base metal thickness and the desired weld penetration.
  • The amount of reinforcement or weld buildup above the base metal surface depends on the application requirements and welding standards. Meet the specified requirements for weld reinforcement while ensuring the structural integrity of the weld.

As a stockist, we maintain AMS 5580 welding electrode and UNS N06600 tig wire in ready supply, so you can get your custom size from our largest options for the lowest price in Mumbai.

Alloy 600 welding rod

Alloy 600 welding rod

AMS 5580 welding electrode

AMS 5580 welding electrode

UNS N06600 tig wire

UNS N06600 tig wire

What are the different types of AMS 5580 filler rods?

AMS 5580 primarily pertains to the seamless tubing of Inconel 600 and does not specify the types of filler rods. Filler rods are typically designated by other specifications which covers nickel and nickel alloy bare welding rods and electrodes.

Therefore, to identify specific types of alloy 600 filler rods, it is advisable to refer to the AWS A5.14 standard. You can also consult with a reputable supplier like Regent Steel & Engineering Co that can provide appropriate options suitable for AMS 5580 filler metal compliance.

We have and can supply Inconel alloy 600 filler rods with a diameter range of 1.6 to 6.4 mm and DIN 2.4816 welding wire with a diameter range of 0.5 to 1.6 mm, so order today!

Inconel 600 filler wire specification
Welding Wire TIG Welding Wire Flux Cored Wire
Dia: 0.5 – 2.0mm Dia : 0.80 To 5.00 mm Dia: 1.0 – 1.6mm.
MIG Welding Wire Inconel 600 welding wire Form Standard
0.6 to 1.0mm. TIG, MIG, FLUX AWS A5.11 ENiCrFe-3
For a great price, we are the certified stockholder of nickel alloy 600 tig rod as per AWS A5.14 in the Gulf countries. Discover more about the different types we provide.
Most selling types of alloy 600 welding rod
Inconel alloy 600 filler rods

Inconel alloy 600 filler rods

  • Dia: 0.06 to2.30 mm
  • Length : upto 350 mm
  • AWS A5.14 ERNiCr-3
DIN 2.4816 welding wire

DIN 2.4816 welding wire

  • AWS A5.11 ENiCrFe-3
  • Inconel 600 welding wire melting point: 1413 °C (2580 °F)
  • DIN 17750, DIN 17742, DIN 17754
Nickel alloy 600 tig rod

Nickel alloy 600 tig rod

  • Flux-Cored Arc Welding
  • MIG Welding
  • TIG Welding
We promise to supply nickel 600 welding electrode, coils and reels with all necessary documents as soon as possible, examining its characteristics.
AMS 5580 welding electrode equivalent
GRADE OLD BRITISH JIS UNS G0ST AFNOR OR
Inconel 600 welding wire EN BS NCF 600 N0600 XH60BT NC15FE11M ЭИ868
NiCr15Fe NA 14
UNS N06600 tig wire mechanical properties
Element Tensile Strength Melting Point Yield Strength (0.2%Offset) Density Elongation
Inconel 600 welding wire Psi – 95,000 , MPa – 655 1413 °C (2580 °F) Psi – 45,000 , MPa – 310 8.47 g/cm3 40 %
Inconel alloy 600 filler rods chemical properties
Grade Cr S Ni Fe Mn C Si P Cu
Inconel 600 welding wire Min %. 14 6
Max%. 17 0.015 72 10 1 0.15 0.5 0.015 0.5
Diameter Chart of DIN 2.4816 tig wire
Inconel 600 welding wire diameter
Thickness
1/4 in. 1/2 in.
1/16 or 3/32 in. 3/32 in.
0.045 or 1/16 in. 1/16 in.
1/8 in. 3/16 in.
1/16 or 3/32 in. 1/8 in.
3/16 in. 1/4 in.
Welding method of UNS N06600 tig rod
Inconel 600 welding wire Method Argon Rate
L/min
Polarity Inter-Pass
Temp. °C
Welding Voltage
V
Welding Current
A
Welding Rate
mm/min
TIG 8~10 DCEN 15~100 15~17 110~130 100~110
SMAW - DCEP 15~100 22~24 120~140 180~200
Size chart of nickel alloy 600 welding rod

Inconel 600 welding wire size chart

RECOMMENDED WELDING WIRE SIZES

MIG SOLID WIRE GASLESS FLUX-CORED WIRE
MATERIAL THICKNESS .045" .030" .024" .035" .035" .030" .045"
22 Gauge (.031) X X X
24 Gauge (.025) X
18 Gauge (.050) X X X X X
20 Gauge (.037) X X X X
14 Gauge (.078) X X X X X X
3/8" (.375) X X
16 Gauge (.063) X X X X X
3/16" (.188) X X X X
1/8" (.125) X X X X X
1/4" (.25) X X X
5/16" (.313) X X X
Ampacity chart of Inconel alloy 600 welding electrodes
Inconel 600 welding wire 75' 50' 125' 325' 100' 175' 150' 225' 200' 275' 250' 300' 350'
AMPs AWG or MCM
100 #2 #4 #1 4/0 #2 1/0 #1 2/0 2/0 3/0 3/0 3/0 4/0
150 #2 #2 1/0 250 #1 3/0 2/0 4/0 3/0 250 4/0 250 350
200 #1 #2 3/0 350 2/0 4/0 3/0 250 4/0 350 350 350
250 1/0 #1 4/0 3/0 250 4/0 350 350 350
300 2/0 #1 4/0 3/0 350 250 350 350
350 3/0 1/0 250 4/0 350 350
400 3/0 2/0 350 250 350
450 4/0 2/0 350 250 350
500 4/0 3/0 350 350
550 250 4/0 350
600 250 4/0 350
Physical properties of AMS 5580 filler metal
Inconel 600 welding wire 200°F 70°F 400°F 800°F 600°F 1000°F
Thermal Expansion X10-6/°F 7.4 5.8 7.7 8.1 7.9 7.7
Density lbs/in3 - 0.306 - - - -
Poisson Ratio - 0.319 0.327 0.312 0.301 0.307 -
Elastic Modulus 103 ksi 30.5 31.1 29.7 27.8 28.8 25.7
Thermal Conductivity Btu-in/h·ft2 ·°F 109 103 121 145 133 139
Yield Strength ksi 26 35 24 21 23 34
Specific Heat Btu/lb·°F 0.111 0.106 0.116 0.126 0.121 0.118
Tensile Strength ksi 75 80 73 69 70 88
How is inconel 600 welding filler wire selected?

When selecting Inconel 600 welding wire, several factors should be considered to ensure compatibility and optimal weld performance. The key factors to consider are:

  • Inconel 600 has a specific composition and the filler wire should have a similar composition to match the base metal. This helps to maintain the desired properties of the weld joint.
  • Consider the welding process being used. Each process may have specific requirements in terms of filler wire diameter, feedability and deposition rate.
  • Evaluate the welding position and the joint configuration to determine the appropriate filler wire size, shape and feeding characteristics.
  • Assess the specific application and requirements of the weld joint. Select a filler wire that offers the necessary properties to meet these requirements.
  • Consider the applicable welding standards and codes. Ensure the chosen filler wire meets the requirements of these standards.
  • Consult the manufacturer's recommendations and technical data sheets for their nickel alloy 600 welding rod. Manufacturers often provide guidance on filler wire selection based on their product's performance and compatibility with Inconel 600.
What is UNS 6600 mig welding?

UNS 6600 MIG welding refers to the process of using Inconel 600 as the base metal for welding and employing the MIG welding process to join the material. This combination is often utilized in applications where the corrosion resistance and high temperature properties of Inconel 600 are required.

UNS N06600 tig rods are widely used in industries like aerospace, chemical processing and power generation. MIG welding offers high productivity and versatility and thus, is a popular choice for joining Inconel 600 components.

DIN 2.4816 threads vs fillers

DIN 2.4816 threads have a cylindrical surface with helical grooves and ridges. It helps in the secure fastening of components. DIN 2.4816 fillers can join two or more metal pieces together, including DIN 2.4816 tig wire. These can be used in welding processes for creating a strong and reliable weld joints.

FAQ
What is the filler wire for Inconel 600?

ERNiCr-3 (NA82)

What is correct alloy 600 welding electrode size?

250 to 450mm.

What are the two types of AMS 5580 filler metal?
  • covered electrodes
  • bare electrode wire
What is application of UNS N06600 tig rod ?
  • Chemical applications
  • Furnace components
  • Flexible metal hose
What is coefficient of expansion of nickel alloy 600 welding rod ?

13.3 μm/m °C (20 – 100°C)

close