Inconel round bar

Inconel is a superalloy that primarily has nickel and chromium in its chemical composition. The inconel round bar is recommended for environments with a lot of moisture. Apart from resisting corrosion and oxidation, the alloy can also withstand pressure and heat in extreme conditions.

This is why the material is used as critical components in jet engines or the aerospace industry. When heat is applied to the material, a thick and protective oxide layer forms on the surface which protects it from further attack.

Inconel round stock also offers excellent mechanical properties like higher tensile strength compared to standard stainless steel alloys. They also possess high strength and durability which makes them suitable for various indoor and outdoor uses.

You can contact Regent Steel & Engineering Co., a reputed inconel alloy round bar supplier in India. Here, you can get customized and high quality round bars at competitive prices along with timely delivery.

We are one of largest and highest-quality Inconel rod and hex bar manufacturer in India, check most common grades

There are different inconel bar grades like 600 & 700 series and N06230.

Why spend extra if you can get the exact size in ASTM B166 Inconel flat bar here? See inconel alloy square bar manufacturing process

Inconel rod

Inconel flat bar

Inconel alloy square bar

• The inconel material is melted in an electric arc furnace, which ensures homogeneity and proper alloying of the elements.
• The molten alloy is then cast into the desired shape followed by heat treatment procedures like annealing. This helps to relieve mechanical stress and enhance the mechanical properties.
• Inconel rod production process might also involve hot working like extrusion or rolling. This is followed by cold drawing which improves the tensile strength and dimensional accuracy of the rods.
• The rods are finally cut and given the desired finish as per the specific application requirements.

As trusted supplier and stockist we provide ASME SB166 inconel bar stock in size range from 3mm to 800 mm at a reasonable cost in Mumbai, know more about other specification

We are here to help you with any inconel cold drawn bar and round stock requirements to fulfil your project's requirements, check various available sizes and shape here

ASTM B166 Inconel hex bar

• 2 to 100 mm
• ASTM B166 | ASME SB166
• Tolerance: H8 to H13

Inconel alloy round bar

• Square
• Round
• Hex

ASME SB166 Inconel bar

• Grinding
• Rough Turned
• Centreless Ground

Get complete technical information of inconel rectangular and bright bar including equivalent, chemical and mechanical composition etc

Common welding techniques like GTAW and GMAW are suggested for inconel flat bars. During the procedure, make sure to use the right filler material and high purity argon as shielding gas. For machining, high speed steel or carbide tools with sharp edges must be used.

The cutting speed must be controlled as inconel tends to work harden quickly. The feed rate should be rightly adjusted to maintain a consistent chip load and prevent excessive tool wear. You can employ techniques like climb milling and peck drilling for hole machining.

• Inconel Round Bar Manufacturer In India produces hot rolled bars by heating a large billet to a high temperature and then passing it through rollers. Cold drawn bars are produced by pulling annealed round bars through a series of dies at room temperature.
• Inconel alloy cold drawn bars have a smoother surface finish than hot rolled ones.
• Cold drawn bars have a finer and uniform grain structure due to controlled deformation at lower temperature conditions.
• Cold drawn inconel square bars have tighter dimensional tolerance and exhibit improved mechanical properties.

• When working with inconel rounds, always wear personal protective equipment. Apart from protective clothes, you should also get protective eye gear, masks, etc, to keep away from metal chips, sparks generated during the production process.
• The workplace must be ventilated properly to manage fumes, dust, etc.
• The right tools and equipment must be used to ensure safety and precision.

• Eddy Current test
• Chemical examination
• Buckling & Crushing test
• Pitting Corrosion Test
• Radiographic Test
• Positive material recognition
• Mechanical examining

• Machining
• SAW Cutting
• Polishing

• Specialty Chemicals
• Condensers
• Sea Water Equipment
• Pharmaceuticals
• Chemical Equipment
• Heat Exchangers
• Pharmaceutical Equipment
• Gas Processing

• 100% Radiography Test Report etc
• Raw Materials Certificate
• Third Party Inspection Report
• EN 10204/3.1B,