Super duplex 2507 pipe fittings

  • Home
  • Super duplex 2507 pipe fittings
Super duplex 2507 pipe fittings
What is the widest temperature range that super duplex pipe fittings can withstand?

Super duplex 2507 pipe fittings can withstand temperature range within -50 ° C to 300 ° C. If this temperature exceeds both above or below the range, performance degradation occurs.

Adding to this, the respective micro-components will experience precipitation with prolonged exposure to relatively high temperatures, and in the case of extreme cold environments, it might suffer from ductility.

While utilizing 2507 pipe cross with the range of suitable environment, one should keep oxidation resistance, excellent performance in sea water environments, low thermal expansion coefficients and high heat conductivity in mind. If not controlled, even these four factors would get affected.

Table of content

Authentic alloy 2507 buttweld fittings manufacturer in India in accordance with ASTM A815, see benefits

What benefits can alloy 2507 buttweld fittings offer?

When looked at this from industrial level, there are many benefits that can alloy 2507 buttweld fittings can offer. This is the best material prone to be used in material testing, such as hardness test. Other than this, following are primary benefits that it can offer:

  • Greater strength than other stainless steels.
  • Greater resistance to crevice corrosions.
  • Inherit more resistance to stress corrosion cracking and erosion.
  • High thermal conductivity capabilities.
  • Low coefficient of thermal expansion.
  • They inherit high energy absorption.

As a supplier provide duplex 2507 elbow and tee in odd sizes in accordance with ANSI/ASME B16.9 at Mumbai, view its welding process

Alloy 2507 buttweld fittings

Alloy 2507 buttweld fittings

2507 stainless steel elbow

2507 stainless steel elbow

UNS S32750 tee

UNS S32750 tee

Can duplex 2507 fittings be welded?

Duplex 2507 fittings can be welded. There are variety of ways in which you can weld this material. In order to check or affect the phase balance (50:50) of Austenite and Ferrite, you can weld heat input and keep check of cooling rate. In order to ensure accurate proportions and excellent mechanical properties, small or excessive heat input should be avoided.

Control the heat input and keep it balanced, somewhat around 5-20 kJ/cm. In situations where we want to drill thin walls, use lower limits of heat. And use the vice versa case when drilling thick walls. Most important factor to note that the temperature should not exceed 100 ° C.

We offer a wide range of ASME SA815 UNS S32750 reducer and stub end in sizes from 1/2′′ to 10′′ (seamless) and 1/2′′ to 48′′ (welded) as well as special orders at reasonable prices

Super duplex 2507 pipe fittings specification
Super duplex 2507 pipe fittings specification

 

Thickness Super duplex 2507 fittings size Standard
Sch 5S to Sch XXS 1/2" to 24" ASME/ANSI B16.9, ASME B16.28
2507 fittings Type Radius Application
Elbow, tee, reducer, cap stub end 1D to 10D or custom Power industry
Super duplex 2507 fittings grades Specification Super duplex 2507 fittings process
UNS S32750/ S32760 ASTM A815 | ASME S A815 Seamless, welded, fabricated
As a stockist, we are able to provide DIN 1.4410 seamless and welded fittings in the best quality. must know its more types
Most popular types of alloy 2507 buttweld fittings
WNR 1.4410 reducer

WNR 1.4410 reducer

  • Welded
  • Seamless
  • Fabricated
Super duplex 2507stub end

Super duplex 2507 stub end

  • Sch 5s to Sch XXS
  • 1/2 to 24 inch NB
  • ASTM A815 | ASME SA 815
UNS S32760 pipe bend

UNS S32760 pipe bend

  • MSS-SP-43
  • ASME/ANSI B16.9
  • ASME B16.28
We offer 2507 stainless steel pipe bend and cross at the most competitive costs with mill TC, check out equivalent, chemical and mechanical properties
2507 stainless steel elbow equivalent
MATERIAL UNS WERKSTOFF NR.
Super duplex 2507 fittings  S32760/S32750  1.4410
UNS S32750 seamless fittings mechanical properties
Super duplex 2507 fittings
Ultimate Tensile Strength, ksi 116 min.
Hardness Rockwell C 32 max.
0.1% Offset Yield Strength 0.2%, ksi 91 min.
Elongation in 2 inches, % 15 min.
0.2% Offset Yield Strength 0.2%, ksi 80 min.
Impact Energy, ft.-lbs. 74 min.
DIN 1.4410 welded fittings chemical properties
Super duplex 2507 fittings Others N C Cr Mo Ni
S=0.001 0.27 0.020 25 4.0 7
What standard sizes are there for 2507 stainless steel elbows?

There are variety of size ranges for 2507 stainless steel elbow yet available. Its standard size ranges between ½’’ to 16’’NB, ERW type ranging between ½’’ to 24’’NB. Based on the above size range.

What is the super duplex 2507 tee's pressure rating?

There are various factors that can affect the pressure rating of a super duplex 2507 tee. Ideal pressure rating ranges between 70,000 to 1,00,000 psi. Due to this they are very highly demanded due to their cheap cost considered as second reason.

It also depends on the size, temperature and design standards of the material that industry demands. Although it is known for its excellent corrosion resistance, dimensions for rating the pressure and its nomenclature should also be kept in mind.

What are the duplex 2507 reducer's common end connections?

The common end connections are covered by standard ASME B16.25, where the buttwelding ends of any pipes are joined into the piping system by the welding methods. Not only this, it also includes welding bevel requirements, preparing for internal ends, for heavy wall components which need shaping internally and externally.

ASTM A815 UNS S32760 reducer dimensions
Super duplex 2507 fittings
NPS OD
D1
OD
D
Length
H
1 - 1/2 21.3 33.4 51
3/4 - 1/2 21.3 26.7 38
1.1/4 - 1/2 21.3 42.2 51
1 - 3/4 26.7 33.4 51
1.1/4 - 3/4 26.7 42.2 51
1.1/2 - 1/2 21.3 48.3 64
1.1/4 - 1 33.4 42.2 51
1.1/2 - 3/4 26.7 48.3 64
1.1/2 - 1.1/4 42.2 48.3 64
1.1/2 - 1 33.4 48.3 64
2 - 3/4 26.7 60.3 76
2 - 1.1/4 42.2 60.3 76
2 - 1 33.4 60.3 76
2 - 1.1/2 48.3 60.3 76
2.1/2 - 1.1/4 42.2 73 89
2.1/2 - 1 33.4 73 89
2.1/2 - 1.1/2 48.3 73 89
3 - 1.1/4 42.2 88.9 89
2.1/2 - 2 60.3 73 89
3 - 1.1/2 48.3 88.9 89
3 - 2.1/2 73 88.9 89
3 - 2 60.3 88.9 89
3.1/2 - 1.1/2 48.3 101.6 102
3.1/2 - 1.1/4 42.2 101.6 102
3.1/2 - 2 60.3 101.6 102
3.1/2 - 3 88.9 101.6 102
3.1/2 - 2.1/2 73 101.6 102
4 - 1.1/2 48.3 114.3 102
4 - 2.1/2 73 114.3 102
4 - 2 60.3 114.3 102
4 - 3 88.9 114.3 102
5 - 2 60.3 141.3 127
4 - 3.1/2 101.6 114.3 102
5 - 2.1/2 73 141.3 127
5 - 3.1/2 101.6 141.3 127
5 - 3 88.9 141.3 127
5 - 4 114.3 141.3 127
6 - 3 88.9 168.3 140
6 - 2.1/2 73 168.3 140
6 - 3.1/2 101.6 168.3 140
6 - 5 141.3 168.3 140
6 - 4 114.3 168.3 140
8 - 3.1/2 101.6 219.1 152
8 - 5 141.3 219.1 152
8 - 4 114.3 219.1 152
10 - 4 114.3 273 178
8 - 6 168.3 219.1 152
10 - 5 141.3 273 178
Dimensions of 2507 stainless steel elbows 45°-90° LR
Super duplex 2507 fittings
OD
D
NPS 45° LR
B
90° LR
A
45° 3D
B
90° 3D
A
26.7 3/4 19 38 24 57
21.3 1/2 16 38
33.4 1 22 38 31 76
48.3 1.1/2 29 57 47 114
42.2 1.1/4 25 48 39 95
60.3 2 35 76 63 152
88.9 3 51 114 95 229
73 2.1/2 44 95 79 190
101.6 3.1/2 57 133 111 267
141.3 5 79 190 157 381
114.3 4 64 152 127 305
168.3 6 95 229 189 457
273 10 159 381 316 762
1219 48 759 1829 1516 3658
219.1 8 127 305 252 610
323.8 12 190 457 378 914
406.4 16 254 610 505 1219
355.6 14 222 533 441 1067
508 20 318 762 632 1524
457 18 286 686 568 1372
559 22 343 838 694 1676
660 26 406 991 821 1981
610 24 381 914 757 1829
711 28 438 1067 883 2134
813 32 502 1219 1010 2438
762 30 470 1143 946 2286
864 34 533 1295 1073 2591
965 38 600 1448 1200 2896
914 36 565 1372 1135 2743
1016 40 632 1524 1264 3048
1118 44 695 1676 1389 3353
1067 42 660 1600 1326 3200
1168 46 727 1753 1453 3505
close